- Street: 31 Rue De Verdun
- City: Montgeron
- State: Arizona
- Country: France
- Zip/Postal Code: 91230
These are just a few of the tools you will require to apply highlights:
* Cape: It is crucial to protect your clothing from bleach stains.
Bowl & Tint Brush:Mix your lightener and developer in a bowl with a tint brush
* Pre-cut Foils I suggest pre-cutting your foils, which can help reduce the time of the entire highlight process. I also recommend buying the highlighting boards that help to create leverage when applying products to hair. It makes it easier to highlight long hair. Place the foil on the top of the board and fold over about an inch or so at the edge. Place the cut or weaved section of hair over the foil. Then, press the foil right up against the scalp and then apply the product. Do not apply the product too heavily on the scalp, this may cause bleeding that isn’t appealing and needs to be fixed.
* Developer and Lightener: Select a lightener that is suitable for your hair and the appropriate developer
* Rat Tail Comb:A rat tail comb can be used to cut hair while highlighting. The two most commonly used methods to highlight hair are slices or a weave. Weaving gives your hair natural appearance. Weaving is created when you cut a small section of hair, then lift it up and weave it in and out using the tail comb releasing hair that doesn’t belong. The word Slicing can be defined as the use of a rat tail comb to section a thin slice of hair and then highlight the entire slice. It gives a more dramatic look. If you are looking for a thicker or more chunky result I recommend cutting two sections back-to back in foils. Instead of leaving hair exposed between foils, cut one section and then slice the other. The more back-to-back cuts you make, the more chunkier the result. Do not attempt to highlight thick hair. I guarantee you that it is an unforgiving experience.
* Water Bottle If you make a mistake using lightener on hair that’s not meant to be highlighted, a water bottle can be utilized. Water slows the process down and 脫毛 – https://www.evrbeauty.com/ dilutes it. After foils have been applied, I would lift the foils to ensure that there is no escape of lightener. If lightener leaks out, then you can cover the foils with water and wipe them with towels. If you notice that the first foils you applied were applied before the foils on the back, open the foil and squirt the foils with water. Do not soak them, but mist them with water. This can slow the process and prevent it from happening., helping to prevent any over highlighted or damaged hair.
* Clips: Clips can aid in organizing your hair, keeping it out of the way as you weave or slice.
If you’re the first time highlighting then I highly recommend that you practice with conditioner. It’s not an easy task and can cause hair damage. So , take a few moments and carefully consider where you want the foils to be placed. It’s better safe than regretting.
Apply a clarifying shampoo and conditioner for several days prior you highlight. This will remove any traces of hair care products , so your hair will be able to take the highlight better.
* Don’t wash your hair for a full day or two before the highlighting process because a small amount of natural hair oil can help protect your hair from chemical damage.
* Cleanse your hair well before you highlight, as tangles can make it difficult to apply highlights and may alter the results.
* You could also test the process with a small section of hair and a little amount of highlighting mix. It is best to wait a few minutes before you test for any adverse effects or damage to your hair. If everything goes well and you are happy with the shade, then you can proceed with the highlighting process.
Lastly, a few application suggestions:
* Start at the back of the head.
* Do not forget to leave hair in between foils.
* Don’t over emphasize the hair.
* To accelerate the process you can heat the foils with the aid of a hair dryer.
* Keep your hair in foils to prevent damage from chemical. Every three minutes, set a timer.
Highlights using a Cap
* Put the cap over your head, and pull it back down gently.
*Utilizing the hook, poke the holes that are marked on the cap as close to your front hair line as you can. Come in at a slight angle for optimal results.
* To create subtle highlights that blend in your hair, cut off a small piece of hair. This is accomplished by not letting the hook to penetrate your hair’s roots deeply. If you want strong, bold highlights, you can pull large sections without digging further into your hair.
Continue pulling hair out until you have the desired number of strands.
* Once hair is pulled through the cap, put on your protective gloves to prepare the highlighting solution.
* To ensure that no hair remains be sure to thoroughly coat all sections.
* Set the timer to the time you want to process.
* Once the time is up remove the cap and wash your hair thoroughly. Don’t shampoo your hair while the cuticle remains open. Washing can cause premature removal
15 toplam, 2 bugün